Tools/Maintenance

RockShox's Suspension Oil comes in different weights to match the most popular suspension fork and shock setups.

Thru Shaft Bleed Plug (Required for Thru Shaft 200 hour service) - RE:Aktiv Thru Shaft Shocks

- Trek Reaktiv Thru Shaft 200 hour service kit

Vivid Air Rear Shock Basic Service Kit - Includes replacement seal, bushing, o-ring, and bottom-out/negative-bumper

Rock-N-Roll Gold lubricant is for both mountain and road bike use. The formulation goes deep down into the chain and traps any dirt. Then, with the energy of the chain freewheeling backwards, the dirt and grit floats to the surface so you can wipe it all off, leaving a new and clean application of lube inside the chain, where it's needed. - All-purpose lube - Cleans and lubricates simultaneously

Problem Solvers 90 degree Presta valve inflator is used to inflate disc wheels, thanks to its narrow, low-profile head. • Presta valve • 90 degree inflator works with most pump heads

The Problem Solvers Suspension Pump Adapter is for use with model-year 1999 to 2000 RockShox SID suspension forks. This aluminum adapter threads into the fork to add air and fine-tune the pressure.

- Exceptional friction reduction and anti-wear properties with greatly reduced friction in metal to metal applications

Uses: - Bearing Grease - "Wax" (application style) Lube - Bike Wash - Degreaser - Rust Remover - Rust Preventer - Anti-Seize - Paint Protectant - Metal Polish - Leather Conditioner Performance: - Substantially reduces friction improving pedaling, shifting and drive train performance - Sheds water - Clean, Lube and Protect with one product - Improved lubrication and wear resistance even when run dry - Temperature performance range from -48F to +600F - Seasons chains and cables after 3-4 applications - State of the art penetrating characteristics - Road, Track, Gravel, CX, MTB, BMX & eBike - Motorcycles - Skateboards Technical: - State of the art Sub-Micron formulation enables the product to be run wet or dry for all riding conditions - Not vegetable oil or vegetable ester based. Will not dry out or gum up - No thermal decomposition even in extreme riding conditions - No Petroleum - No Alcohol Environmental: - Green Engineered - Bio-based Product - Non-Toxic - Biodegradable - USDA Certified - Made in the USA with USA raw ingredients Meets or Exceeds: - MIL-PRF-6340E ASTM D93 Flash Point - MIL-PRF-6340E ASTM D445 Kinematic Viscosity 104 F - MIL-PRF-6340E ASTM D4172 Wear Preventative Characteristics - MIL-PRF-6340E ASTM D5620 Load Carrying Capacity Jaw Load - MIL-PRF-6340E ASTM Corrosion Production - ASTM D 5183, Determination of the Coefficient of Friction for Lubricants: No Fail

- Makes your bike shine like new and keeps it that way. - Biodegradable formula cleans, polishes, and protects in one step. - Also great for dropper posts, suspension, and for seating tire beads. The original bike polish, Bike Lust's proprietary silicone-based formula includes a biodegradable cleaning agent. Bike lust goes on wet, quickly cleaning light dirt and grime as it polishes, and then dries to a beautiful protective coating. Works on any surface or material in one simple step making your bike look like new and future cleaning easier! Also great for dropper posts, suspension, and for seating tire beads. Bike Lust can be used on all types of materials and finishes including carbon fiber and matte finishes. It's also fantastic on tires to help shed mud and dirt as you ride.

Foaming Bike Wash RTU Spray Bottle - Advanced plant-derived surfactants quickly remove tough dirt and grime from the whole bike. - Use on the whole bike without risk of damage or washing away grease/lube from critical parts. - Safe, biodegradable, phosphate-free, solvent-free, plant-derived, and zero-VOC. - Available in ready-to-use (RTU) trigger sprayer bottles and 16X Concentrate. The improved Green Fizz bike wash safely, naturally, & effectively removes tough dirt & grime from the whole bike. Developed specifically for bicycle washing, Green Fizz can safely be used on any material without risk of damage or washing away grease/lube from critical parts. The pre-activated, biodegradable formula uses advanced plant-derived surfactants and incredible foaming action to reach surfaces and loosen dirt allowing it to be easily wiped or rinsed away leaving your bike looking like new. Free of harsh chemicals, gentle enough to use on any material, fully biodegradable, phosphate-free, solvent-free, plant-derived, and zero-VOC. Our 16X concentrate offers great value, reduction in packaging, and reduced shipping costs. 16oz of concentrate makes 8+ Liters of Green Fizz RTU!

Green Fizz's biodegradable solvent-free formula can be safely used on all parts and materials, including carbon fiber, without washing away grease and lubricants or damaging delicate parts. - Advanced plant-derived surfactants quickly remove tough dirt and grime from the whole bike - Use on the whole bike without risk of damage or washing away grease/lube from critical parts - Safe, biodegradeable, phosphate-free, solvent-free, plant-derived, and zero-VOC - Can be used with or without water

- 220 gram, 21-function folding multi-tool with 2.5, 3, 4, 5, 6, & 8mm hex, T25 & T30 Torx, #2 Phillips & flat blade screwdrivers, 1-13 speed chain tool, 2 tire levers, 7 & 8mm flare box wrenches, 3.23, 3.3, & 3.45 spoke wrenches, bottle opener, Shimano crank cap tool, and Presta valve core tool. - Professional-grade tool steel wrenches feature superior anti-corrosion finish for unmatched lasting performance. - Ergonomic body made of light but tough composite material. The ICM won't just get you home, but will keep your ride going! First introduced in 2004, this proven design continues to win acclaim from editors and riders alike. The new ICM-21 adds new tools including a 1-13 speed chain tool, a Shimano Hollowtech crank cap tool, and 7 & 8mm flare wrenches for disc brake fittings, all while dropping 15 grams of weight. The ICM-21 features tools made from heat-treated tool steel for strength, superior anti-corrosion finish for unmatched lasting performance, a body made of lightweight but super tough composite material, and two full-function tire levers.

The Pro Saw Guide's full metal construction delivers straight, precise, and clean cutting of all threadless steerer tubes from 1" to 1.5", handlebars, and many sizes of seatposts. The efficient design provides a balance of simple form and good work-piece visibility, while also providing secure hold and precise alignment. - Full metal construction with aluminum jaws and hardened steel guide plates for straight cuts every time. - Fits tube sizes from 19mm to 39mm (0.75" to 1.5"); everything from handlebars to 1.5" steerers. - Laser etched sizing scale provides quick reference of jaw position. - Easily set slot width for standard or carbon blades by moving spacer plate position.

- The original synthetic chain lube formulated specifically for mountain bikes. - New formula lasts even longer and is dye-free. - Superior wear protection, efficiency and durability for extreme conditions/mileage. - Unique detergents break down and isolate dirt protecting the surfaces of your chain. This is the product that started it all back in 1989. This breakthrough lubricant revolutionized the entire chain lube market. This full synthetic lubricant is designed to handle the harshest conditions and outlast other lubes in all conditions. Syn Lube is formulated with extreme pressure additives, corrosion inhibitors, and tackifiers to provide incredible wear protection, lubrication, and staying power in extreme wet and muddy conditions. Unique polymer detergents also work to break down dirt protecting the surfaces of your chain. Go ahead, play in the mud.

- Durable double-ended brush - Ideal for chains, cogs, derailleurs, and chainrings. - Recommended for use with Pedro's cleaner and degreaser products. - Solvent resistant synthetic handle and bristles. - Not recommended for oral use. Pedro's Toothbrush is designed to tackle the drivetrain and is ideal for cleaning chains, cogs, derailleurs, and chainrings. The ergonomic handle is paired with two purpose built brush features. The tapering length bristles up front are designed to scrub the intricate surfaces of chains, chainrings and cassettes while at the opposite end, longer, stiffer, larger-diameter bristles reach deep between the cassette cogs removing even the deepest dirt and grime. The Pedro's Toothbrush can also be a great tool for applying degreaser to drivetrain parts. While holding the Toothbrush flat with the bristles out to the side, pour degreaser to the bristles. Then quickly move the toothbrush to the drivetrain and apply the degreaser using a light scrubbing motion. This technique works especially well with Pedro's Degreaser 13.

Having the right tool for the job is essential when working on modern bicycles. Pedro's Universal Crank Remover provides the tools required to properly remove press fit square taper and splined cranks. Unlike similar items offered by the competition, Pedro's includes everything you need in one convenient package The Universal Crank Remover fits all cranks using 22mmx1 threads and square, tapered bottom bracket spindles and splined Shimano Octalink and ISIS Drive bottom bracket spindles that do not use a “self extracting” system.

Park combines the three most used bolt sizes into one convenient wrench. The 3-Way Sprocket Wrench sports 8, 9 and 10mm sockets made from forged chrome-vanadium steel in Park's classic Y-shape that offers plenty of leverage and a comfortable grip.

Park Tool introduced the bicycle world to the 3-way hex wrench set over 30 years ago. Our 3-way wrenches fit perfectly in the palm of the hand and provide excellent leverage, making them a favorite of countless shop mechanics worldwide. AWS-1 FEATURES - 4mm, 5mm, and 6mm hex set - Wrenches made from industrial tool steel, through hardened and tempered for long life - Chamfered tips for a perfect fit

Park Tool's 106-AC easily adapts the #106 Work Tray or PTH-1 Paper Towel Holder to fit 35mm-37mm upright tubes on PCS-9 Repair Stands, as well as 2003 and newer PCS-1, PCS-4, PCS-4-1, PCS-4-2 Repair Stands.

Park's Bottom Bracket Wrench has 2 ends to fit slotted bottom bracket adjusting cups and cups with raised 16mm wrench flats common on older English and less-expensive bicycles. Please ask if you have any questions whether this wrench is right for your repair.

Park's AV-1 Axle Vise makes repairing and overhauling hubs easier than ever. It prevents your axle from spinning while work is done on the hub and it has two different size receptacles so it will work with both front and rear axles.

The BKD-1 Hydraulic Brake Bleed Kit will bleed most models of DOT-fluid-based hydraulic brakes. Hydraulic systems need bleeding to remove any air bubbles and to inject new, clean fluid. - Designed and built for home use and the rigors of daily commercial use - Includes two syringes, hoses with shutoff clips, multi-size bleed blocks and a unique attachable syringe mount - Housed in a rugged reusable case - Machined stainless steel and 7075 aluminum fittings to service SRAM, Hayes, Formula, Hope and other brands of DOT-fluid-based hydraulic brake systems - Replacement parts available - Brake fluid not included

The BKD-1.2 Hydraulic Brake Bleed Kit will bleed most models of DOT fluid-based hydraulic disc brakes, including models made by SRAM®, Formula®, Hayes®, and Hope®. Bleeding of hydraulic brakes removes air bubbles and contaminants from the braking system, for long-lasting components and peak performance. The BKD-1.2 is built for the rigors of daily commercial use and includes two syringes, hoses with shutoff clips, multi-size bleed blocks, and a set of our unique mountable syringe holders, as well as multiple hose fittings to fit the multiple standards found on hydraulic bicycle brake systems. Every part is replaceable and available from Park Tool. Housed in a rugged storage case. Includes: - Two 20 mL syringes Two hose assemblies with shutoff clips - Two 10 mm/12 mm universal bleed blocks - Two 11 mm bleed blocks for Hayes® systems -  Two adjustable syringe holders -  M5 x 0.8 adapters— SRAM® (x2) -  M6 x 1.0 adapter— universal (x2) - Bleeding Edge-specific fitting — SRAM® -  Hose compression sleeve — universal -  Set of spare O-rings and hose -  Replacement parts available -  Brake fluid not included NOTE: The BKD-1.2 is for DOT fluid-based hydraulic bicycle brake systems only. DOT fluid and mineral oil should never be mixed in the brake system or in their respective service tools. Cross-contamination of brake fluid may cause seal failure which may result in brake failure. For mineral oil brake systems use the Park Tool BKM-1.2 Hydraulic Brake Bleed Kit — Mineral Oil.

The BKM-1.2 Hydraulic Brake Bleed Kit will bleed most models of mineral oil-based hydraulic bicycle disc brakes, including models made by Shimano®, Magura®, TRP®, Tektro®, Trick Stuff®, SRAM® DB8, Campagnolo®, Promax®, and Clarks®. Bleeding of hydraulic brakes removes air bubbles and contaminants from the braking system, for long-lasting components and peak performance. The BKM-1.2 is built for the rigors of daily commercial use and includes two syringes, hoses with shutoff clips, multi-size bleed blocks, a bleed funnel, and a set of our unique mountable syringe holders, as well as multiple hose fittings to fit the multiple standards found on hydraulic bicycle brake systems. Every part is replaceable and available from Park Tool. Housed in a rugged storage case. Includes: -  Two 20 mL syringes -  Two hose assemblies with shutoff clips -  One hose assembly with integrated fitting for bleed nipples such as those found on Shimano® mineral oil brake systems -  One open-ended hose assembly -  Bleed funnel with stopper -  Two 10 mm/12 mm universal bleed blocks -  Two 11 mm bleed blocks -  Two adjustable syringe holders -  M4 x 0.7 adapters — SRAM® DB8, Trick Stuff®, Campagnolo® (x2) -  M5 x 0.8 adapter — Formula™ Cura™, Tektro®, Hayes® (x2) -  M6 x 0.75 adapter — Magura® -  M6 x 1.0 adapters — universal (x2) -  M6 x 1.0 adapter — Promax® -  M7 x 0.75 adapter — Shimano® -  Hose compression sleeve — universal -  Fluid disposal bag -  Set of spare O-rings and hose -  Replacement parts available -  Brake fluid not included NOTE: The BKM-1.2 is for mineral oil-based hydraulic bicycle brake systems only. DOT fluid and mineral oil should never be mixed in the brake system or in their respective service tools. Cross-contamination of brake fluid may cause seal failure which may result in brake failure. For brakes using DOT fluid use the Park Tool BKD-1.2 Hydraulic Brake Bleed Kit — DOT.

Bio ChainBrite Bicycle Chain and Component Cleaning Fluid is a 100% biodegradable, natural, plant-based degreaser formulated for use in Park's CM-5.2 Cyclone Chain Scrubber or as a general purpose degreaser. It won't harm alloy, plastic, or rubber parts. Use CB-4 full strength, do not dilute with water. Cover parts in solvent and scrub using a brush. 16-ounce bottle

Park's BBT-18 is a heavy duty, investment cast tool for installing and removing all Shimano, ISIS Drive, and ISIS Overdrive 8-notch bottom bracket cups.

The Bottom Bracket Wrench removes and installs Shimano Hollowtech II, Race Face X-type, FSA MegaExo, Campagnolo Ultra-Torque and TruVativ Giga X-pipe bottom brackets. Laser cut for a precise fit, one end of the BBT-9 securely engages the 16 cup notches, while the other end engages the 8 internal splines of the crankarm adjustment cap.

A dirty drivetrain causes poor shifting and unnecessary wear to expensive parts. The Chain Gang contains everything needed to quickly and easily clean the chain, freewheel cogs, and chainrings. The Chain Gang includes: - CM-5.3 Cyclone Chain Scrubber - GSC-1 GearClean Brush - 8 oz. bottle of Bio ChainBrite The CG-2.4 works on nearly any bike, including multi-speed, single-speed, and e-bikes.

A fast and convenient tool to remove and install 12-spline Shimano/SRAM style cassette lockrings, as well as similar lockrings on rotor discs. The FR-5H features a modified FR-5 tool that allows use without removing most quick release skewer nuts. The removable, threaded steel handle makes it possible to replace a worn or damaged head. - Fits Shimano, SRAM (including 1x), SunRace, SunTour, Chris King and other cassette lockrings - Also fits some Shimano disc brake lockrings

A worn chain shifts poorly and wears sprockets at an accelerated rate. Park Tool's Chain-Wear Indicator is a “go-no go” gauge designed to accurately indicate when a chain reaches .5% and .75%, the points at which most chain manufacturers suggest replacement. The updated CC-3.2 is longer, more accurate and features permanent measurement markings.

Park's Chainring Nut Wrench makes chainring bolt installation and removal easy. It securely holds the slotted nut to prevent spinning when tightening or loosening the bolt. And, it's double-ended to fit most slotted-type nuts, including Campagnolo chainring bolt nuts.

Park's Crank Puller is for removing crankarms on Shimano's splined, oversize, pipe-billet bottom brackets. It employs a long handle and a fine thread for the leverage and torque needed to remove tight arms. Park's unique rotating tip ensures smooth operation and long life. (The CCP-44 does not fit standard square or tapered bottom brackets.)

Park's Double-Ended Cone Wrenches are designed for home mechanics. They're made of thin tool steel to fit the low-clearance adjusting nuts and cone flats on a variety of bearing assemblies. Each wrench is chrome plated for long life and available in popular combinations from 11 to 18mm. Most applications require a pair of cone wrenches. Call or stop by. We can recommend the correct sizes for your needs.

The Park FR-7 Freewheel Remover fits Falcon freewheels. It's built thin so that removing axle parts is unnecessary. And, it's constructed of durable heat-treated steel.

12 splines, 22.6mm diameter fits Shimano, Sachs Aris, Sun Race, DNP Epoch, and other 5–10 speed freewheels. The FR-1.3 includes an enlarged thru-hole to accommodate 14mm axles.

This dual-sided brush is specifically designed for cleaning hard-to-reach areas of the bicycle drivetrain. The long, stiff bristles of the GSC-3 are narrow enough to reach between the gears of tightly-spaced modern cassettes, while the slim contoured end is capable of picking grit and grime out of tight spaces such as derailleur pulley wheels.

Park's Gear Clean Brush has a handle on one end with a curved, serrated edge perfect for cleaning between cassette cogs. The other end's tough nylon bristles are ideal for cleaning the derailleurs, chain and other drivetrain parts to keep them clean and prevent premature wear. It also works great on brakes and other components that collect dirt and grime. The GearClean easily fits in a toolbox or pack.

The HCW-16.3 is a combination 15mm pedal wrench and chain whip. Use for both pedal removal/installation and for cassette removal. Chain whip features improved compatibility with 5-speed to 12-speed mountain and road bike cassettes and freewheels. The HCW-16.3 is 10.75" long (27.3cm).

Park's versatile Headset Wrench is constructed from hardened, laser-etched steel for the maximum in durability and precision. The HCW-6 features a 32mm headset wrench on one end and a 15mm pedal wrench on the other.

HPG-1 Park Tool High Performance Grease is proprietarily blended to meet the demanding needs of today’s high performance bicycles and high end components. -Superior adherence and extended lubrication life -Extreme temperature range: -20°F to 540°F (-29°C to 282°C) -Highly water resistant -Perfect for high end applications including precision ground and ceramic bearings, pivots and suspension components 4-ounce (113 g) tube

Park's AWS-7 features a Y-shaped nylon handle with 4 and 5mm Allen wrenches and a T25 Torx wrench. This convenient 3-in-1 tool keeps commonly used wrenches together and offers an excellent grip as well.

Park's Home Mechanic Pedal Wrench is great for your home workshop and event tool box. This top-quality 15mm pedal wrench provides the leverage you need to remove stubborn pedals. It's made to last from heat-treated steel, and the handle has a vinyl grip for comfort.

Park's Hydraulic Brake Piston Press is used to set or reset the piston(s) inside hydraulic disc brake calipers during installation, maintenance and repair. Just push it into the caliper to wedge the piston into place. It's made of tough tool steel with a comfortable and oversize rubber handle for a great grip.

"Take the guesswork out of internal routing. The IR-1.3 speeds the installation of internally-routed cable, housing, electronic wiring and hydraulic hose into carbon fiber, titanium, and aluminum frames. The straightforward guide magnet system utilizes five long guide cables with unique fittings, which can be routed through the frame in a number of ways using the included guide magnet. Everything is neatly stored in a convenient compact case. A true time and frustration saver!??Includes five 188 cm (74"") guide cables with attached magnets and unique fittings: • Barbed adapter — Threads into the end of brake & shift cable housing as well as hydraulic brake hose • Rubber adapter — Securely holds electronic shifting wire such as Shimano® Di2, SRAM® RED® eTAP®, FSA® K-Force® WE®, and Campagnolo® EPS • Di2®-specific adapter — Specially-designed connector clips into the end of Shimano® E-tube® Di2® shift wire, and is perfectly sized to fit into frame holes as small as 6 mm • Di2® EW-SD300-specific adapter — Specially-designed connector clips into the end of Shimano® E-tube® Di2® EW-SD300 shift wire • Reverse-polarity magnet — Used in conjunction with any of the other guide cables - feeds into the opposite end and meets the leading cable in the middle, aiding in routing on frames with tricky interior shapes Also included: • Double-threaded barb — Securely attaches new housing or hydraulic hose to existing housing or hose, allowing for easy replacement without redoing the routing • Guide magnet — routes guide cables through the frame from the outside"

Park's Mini Chain Brute Chain Tool goes anywhere and features a V-shaped handle, a super-strong replaceable pin, and fine threads to make chain removal and installation a breeze. The CT-5 works on any derailleur chain, including Shimano Hyperglide and 9-, 10-, and 11-speed. It works for loosening tight links, too.

Choose the perfect tool for the job with Park's P-Handled Hex Wrenches. These top-shelf Allen wrenches come with offset handles made from durable nylon in a comfortable, ergonomic design. They are made of chrome vanadium for exceptional durability. The long shafts feature Bondhus heads for accessing hard-to-reach bolts and the short ends are chamfered for extra grip and high-torque applications.

They always say, the right tool for the right job. Park's P-handled Torx Wrenches are available in T6, T8, T10, T15, T20, T25, T30 and T40 sizes. They feature offset handles made from durable nylon with a comfortable, ergonomic design. The wrenches are made of high-torque industrial steel for excellent durability.

"The PCS-9.3 is a basic folding bicycle workstand designed and built for the home mechanic – a stable way to hold nearly any bike off the ground for adjustments, cleaning and repair. Features 18"" (460 mm) of height adjustment and 360 degrees of clamp rotation, positioning all parts of the bike within reach for any mechanic whether seated or standing. The stand's all-steel construction with teardrop-shaped tubing ensures maximum rigidity and stability, with a locking support yoke and upgraded internals for extra dependability. The PCS-9.3 is able to hold up to 80 lbs. (36 kg), which allows for compatibility with virtually all two-wheeled pedal-driven bicycles, including fat bikes and most e-bikes.* The PCS-9.3 quickly folds down for storage and transport with a smooth-operating leg support system that pulls both legs up in one simple motion. The PCS-9.3 is the perfect way to upgrade your home shop. NOTE: The maximum weight capacity of the PCS-9.3 assumes the weight is centered below the clamp and between the legs.? - Fully adjustable clamp fits 7/8"" to 3"" (22 mm–76 mm) diameter tubes and seat posts of any shape and material, including aero posts and dropper posts - Narrow clamping jaws (2.7""/70 mm) fit into tight areas or on short seat posts - Durable textured powder coat finish - Maximum weight capacity: 80 lbs. (36 kg) - Height adjustable from 39"" to 57"" (990 mm–1450 mm) - Base when open forms a triangle of 36"" x 36"" x 48"" (920 mm x 920 mm x 1210 mm) - Folds down to 44"" x 14.5"" (1140 mm x 370 mm) - Weight: 16 lbs. (7.2 kg) - #2848A quick-release collar with accessory pods required for use of PTH-1 Paper Towel Holder or 106 Work Tray"

Park's PolyLube is specifically formulated to protect bearing components. Its Polyurea grease has extremely high shear strength to protect bottom brackets, headsets, pedals and hubs. Use it on threads, seatposts, stems and cables, too. It's also safe for fork seals, and repels water.

Park's PolyLube is specifically formulated to protect bearing components. Its Polyurea grease has extremely high shear strength to protect bottom brackets, headsets, pedals and hubs. Use it on threads, seatposts, stems and cables, too. It's also safe for fork seals, and repels water.

Park Tool's Replacement Chain Tool Pin (2-Pack) fits Park Tool's CT-1, CT-2, CT-3, CT-3.2, CT-5, and CT-7 Chain Tools. • Made from hardened alloy tool steel • Uses 7mm or 9/32" 12 pt box end/socket • Sold singly or in pairs

If you have a bike with disc brakes, you'll want Park's Rotor Truing Fork. It allows you to gently adjust bent and damaged disc-brake rotors. It's made from high-quality steel and features 2 laser-cut slots for precise adjustments and a vinyl handle for comfort and control.

Park's Pin Spanners are designed for maximum usefulness and versatility at the best value. Tough high-carbon tool steel is used to ensure long life and the handles are vinyl coated for a great grip and color-coded for easy identification. The green-handled SPA-1 is used to turn the adjustable bottom-bracket cup found on most 3-piece cranksets.

Park's Cone Wrenches are made of durable tool steel and are nice and thin to fit on the small-clearance cones found on hubs and other bearing assemblies. Plus, they work as regular wrenches, too. They feature Park's special Y heads that put more material where it's needed for excellent durability and strength. Most applications require at least 2 cone wrenches. If you have questions please contact us and we can recommend the correct sizes for your needs.

Park's professional-quality, precision-sized spoke wrenches are hardened and chrome plated for long service. Wrenches are vinyl coated in one of four colors indicating the size at a glance. You will find these wrenches in virtually every professional bike shop and every shop mechanic's personal tool stash. Make sure you have the sizes you need in your home toolbox and bike bag.

Because even your reliable Mavic wheels will eventually need truing, Park offers their Spoke Wrench For Mavic Wheel Systems. This comfortable, vinyl-coated, double-ended spoke wrench easily accesses and turns Mavic nipples. One end fits Mavic 6-spline, 9mm threaded eyelets and the other fits their 7-spline, 6.4mm nipples.

Shop quality L-shaped, high torque industrial steel Torx compatible wrenches. Featuring chamfered tips, tight tolerances and a handy portable tool holder for easy access. Includes: T9, T10, T15, T20, T25, T27, T30 and T40.

Park's Torx Wrench Set is just what you need to make repairs on many of your bike parts that use Torx (star-shaped) fittings, such as disc brakes, pedals, chainring bolts, and others. It offers the common bicycle wrench sizes (T7, T9, T10, T15, T20, T25, T27, T30 and T40) in a convenient fold-up set. Its composite handle is super strong, comfortable to use and slip resistant.

• Updated to fit better in the hand with a more rounded, smoother shape • The precision sized SW-7.2 fits the three most popular spoke nipple sizes on the market • Nickel plated for years of service • Designed for the home mechanic. FIts the following size spoke nipples: • .127" (3.23mm) • .130" (3.30mm) • .136" (3.45mm)